Lost-wax casting






A model of an apple in wax




From the model a rubber mould is made. (The mould is shown here with a solid cast in plaster)




From this rubber mould a hollow wax or paraffin cast is made




The hollow paraffin apple is covered with a final, fire-proof mould, in this case clay-based, an open view. The core is also filled with fire-proof material. Note the stainless steel core supports. In the next step (not shown), the mould is heated in an oven upside-down and the wax is "lost"




Liquid bronze at 1200 °C is poured into the dried and empty casting mould




A bronze cast, still with spruing




On the left is an example of a rubber mould, often used in the lost-wax process, and on the right is the finished bronze sculpture.


Lost-wax casting (also called "investment casting", "precision casting", or cire perdue which has been adopted into English from the French)[1] is the process by which a duplicate metal sculpture (often silver, gold, brass or bronze) is cast from an original sculpture. Intricate works can be achieved by this method.


The oldest known example of this technique is a 6,000-year old amulet from Indus valley civilization.[2] Other examples from a similar period are the objects discovered in the Cave of the Treasure (Nahal Mishmar) hoard in southern Israel, and which belong to the Chalcolithic period (4500–3500 BC). Conservative estimates of age from carbon-14 dating date the items to c. 3700 BC, making them more than 5,700 years old.[3][4]. Lost-wax casting was widespread in Europe until the 18th century, when a piece-moulding process came to predominate.


The steps used in casting small bronze sculptures are fairly standardized, though the process today varies from foundry to foundry. (In modern industrial use, the process is called investment casting.) Variations of the process include: "lost mould", which recognizes that materials other than wax can be used (such as: tallow, resin, tar, and textile);[5] and "waste wax process" (or "waste mould casting"), because the mould is destroyed to remove the cast item.[6][7]




Contents






  • 1 Process


  • 2 Casting jewellery and small parts


  • 3 Textile use


  • 4 Archaeological history


    • 4.1 Middle East


    • 4.2 Near East


    • 4.3 South Asia


    • 4.4 Egypt


    • 4.5 Greek, Roman and Mediterranean


    • 4.6 East Asia


    • 4.7 Southeast Asia


    • 4.8 Northern Europe


    • 4.9 West Africa


    • 4.10 Latin America




  • 5 Literary history


    • 5.1 Indirect evidence


    • 5.2 Direct evidence


      • 5.2.1 India


      • 5.2.2 Theophilus


      • 5.2.3 America






  • 6 Gallery


  • 7 Notes


  • 8 References


  • 9 External links





Process


Casts can be made of the wax model itself, the direct method, or of a wax copy of a model that need not be of wax, the indirect method. These are the steps for the indirect process:




  1. Model-making. An artist or mould-maker creates an original model from wax, clay, or another material. Wax and oil-based clay are often preferred because these materials retain their softness.


  2. Mouldmaking. A mould is made of the original model or sculpture. The rigid outer moulds contain the softer inner mould, which is the exact negative of the original model. Inner moulds are usually made of latex, polyurethane rubber or silicone, which is supported by the outer mould. The outer mould can be made from plaster, but can also be made of fiberglass or other materials. Most moulds are made of at least two pieces, and a shim with keys is placed between the parts during construction so that the mould can be put back together accurately. If there are long, thin pieces extending out of the model, they are often cut off of the original and moulded separately. Sometimes many moulds are needed to recreate the original model, especially for large models.


  3. Wax. Once the mould is finished, molten wax is poured into it and swished around until an even coating, usually about ​1⁄8 inch (3 mm) thick, covers the inner surface of the mould. This is repeated until the desired thickness is reached. Another method is to fill the entire mould with molten wax and let it cool until a desired thickness has set on the surface of the mould. After this the rest of the wax is poured out again, the mould is turned upside down and the wax layer is left to cool and harden. With this method it is more difficult to control the overall thickness of the wax layer.


  4. Removal of wax. This hollow wax copy of the original model is removed from the mould. The model-maker may reuse the mould to make multiple copies, limited only by the durability of the mould.


  5. Chasing. Each hollow wax copy is then "chased": a heated metal tool is used to rub out the marks that show the parting line or flashing where the pieces of the mould came together. The wax is dressed to hide any imperfections. The wax now looks like the finished piece. Wax pieces that were moulded separately can now be heated and attached; foundries often use registration marks to indicate exactly where they go.


  6. Spruing. The wax copy is sprued with a treelike structure of wax that will eventually provide paths for the molten casting material to flow and for air to escape. The carefully planned spruing usually begins at the top with a wax "cup," which is attached by wax cylinders to various points on the wax copy. The spruing does not have to be hollow, as it will be melted out later in the process.


  7. Slurry. A sprued wax copy is dipped into a slurry of silica, then into a sand-like stucco, or dry crystalline silica of a controlled grain size. The slurry and grit combination is called ceramic shell mould material, although it is not literally made of ceramic. This shell is allowed to dry, and the process is repeated until at least a half-inch coating covers the entire piece. The bigger the piece, the thicker the shell needs to be. Only the inside of the cup is not coated, and the cup's flat top serves as the base upon which the piece stands during this process.


  8. Burnout. The ceramic shell-coated piece is placed cup-down in a kiln, whose heat hardens the silica coatings into a shell, and the wax melts and runs out. The melted wax can be recovered and reused, although it is often simply burned up. Now all that remains of the original artwork is the negative space formerly occupied by the wax, inside the hardened ceramic shell. The feeder, vent tubes and cup are also now hollow.


  9. Testing. The ceramic shell is allowed to cool, then is tested to see if water will flow freely through the feeder and vent tubes. Cracks or leaks can be patched with thick refractory paste. To test the thickness, holes can be drilled into the shell, then patched.


  10. Pouring. The shell is reheated in the kiln to harden the patches and remove all traces of moisture, then placed cup-upwards into a tub filled with sand. Metal is melted in a crucible in a furnace, then poured carefully into the shell. The shell has to be hot because otherwise the temperature difference would shatter it. The filled shells are then allowed to cool.


  11. Release. The shell is hammered or sand-blasted away, releasing the rough casting. The sprues, which are also faithfully recreated in metal, are cut off, the material to be reused in another casting.


  12. Metal-chasing. Just as the wax copies were chased, the casting is worked until the telltale signs of the casting process are removed, so that the casting now looks like the original model. Pits left by air bubbles in the casting and the stubs of the spruing are filed down and polished.


Prior to silica-based casting moulds, these moulds were made of a variety of other fire-proof materials, the most common being plaster based, with added grout, and clay based. Prior to rubber moulds gelatine was used.



Casting jewellery and small parts


The methods used for small parts and jewellery vary somewhat from those used for sculpture. A wax model is obtained either from injection into a rubber mould or by being custom-made by carving. The wax or waxes are sprued and fused onto a rubber base, called a "sprue base". Then a metal flask, which resembles a short length of steel pipe that ranges roughly from 1.5 to six inches tall and wide, is put over the sprue base and the waxes. Most sprue bases have a circular rim which grips the standard-sized flask, holding it in place. Investment (refractory plaster) is mixed and poured into the flask, filling it. It hardens, then is burned out as outlined above. Casting is usually done straight from the kiln either by centrifugal casting or vacuum casting.


The lost-wax process can be used with any material that can burn, melt, or evaporate to leave a mould cavity. Some automobile manufacturers use a lost-foam technique to make engine blocks. The model is made of polystyrene foam, which is placed into a casting flask, consisting of a cope and drag, which is then filled with casting sand. The foam supports the sand, allowing shapes that would be impossible if the process had to rely on the sand alone. The metal is poured in, vaporizing the foam with its heat.


In dentistry, gold crowns, inlays and onlays are made by the lost-wax technique.Application of Lost Wax technique for the fabrication of cast inlay was first reported by Taggart. A typical gold alloy is about 60% gold and 28% silver with copper and other metals making up the rest. Careful attention to tooth preparation, impression taking and laboratory technique are required to make this type of restoration a success. Dental laboratories make other items this way as well.



Textile use


In this process, the wax and the textile are both replaced by the metal during the casting process, whereby the fabric reinforcement allows for a thinner model, and thus reduces the amount of metal expended in the mould.[8] Evidence of this process is seen by the textile relief on the reverse side of objects and is sometimes referred to as "lost-wax, lost textile". This textile relief is visible on gold ornaments from burial mounds in southern Siberia of the ancient horse riding tribes, such as the distinctive group of openwork gold plaques housed in the Hermitage Museum, Saint Petersburg.[8] The technique may have its origins in the Far East, as indicated by the few Han examples, and the bronze buckle and gold plaques found at the cemetery at Xigou.[9] Such a technique may also have been used to manufacture some Viking Age oval brooches, indicated by numerous examples with fabric imprints such as those of Castletown (Scotland).[10]



Archaeological history




Replica of bronze sceptre from the Nahal Mishmar Hoard.



Middle East


Some of the oldest known examples of the lost-wax technique are the objects discovered in the Cave of the Treasure (Nahal Mishmar) hoard in southern Israel, and which belong to the Chalcolithic period (4500–3500 BC). Conservative Carbon 14 estimates date the items to c.3700 BC, making them more than 5700 years old.[3][4]



Near East


In Mesopotamia, from c. 3500–2750 BC, the lost-wax technique was used for small-scale, and then later large-scale copper and bronze statues.[3] One of the earliest surviving lost-wax castings is a small lion pendant from Uruk IV. Sumerian metalworkers were practicing lost-wax casting from approximately c. 3500–3200 BC.[11] Much later examples from northeastern Mesopotamia/Anatolia include the Great Tumulus at Gordion (late 8th century BC), as well as other types of Urartian cauldron attachments.[12]




Making sculpture using a lost wax process at Bastar district, Chhattisgarh, India



South Asia


The oldest known example of the lost-wax technique comes from a 6,000-year-old copper, wheel-shaped amulet found at Mehrgarh, Pakistan.[13]


Metalcasting by the Indus Valley Civilization began around 3500 BC in the Mohenjodaro area,[14] which produced one of the earliest known examples of lost-wax casting, an Indian bronze figurine named the “dancing girl” that dates back nearly 5,000 years to the Harappan period (c. 3300–1300 BC).[14][15] Other examples include the buffalo, bull and dog found at Mohenjodaro and Harappa,[5][15][16] two copper figures found at the Harappan site Lothal in the district of Ahmedabad of Gujarat,[14] and likely a covered cart with wheels missing and a complete cart with a driver found at Chanhudaro.[5][16]


During the post-Harappan period, hoards of copper and bronze implements made by the lost-wax process are known from Uttar Pradesh, Bihar, Madhya Pradesh, Odisha, Andhra Pradesh and West Bengal.[14] Gold and copper ornaments, apparently Hellenistic in style, made by cire perdue were found at the ruins at Sirkap. One example of this Indo-Greek art dates to the 1st century BC, the juvenile figure of Harpocrates excavated at Taxila.[14] Bronze icons were produced during the 3rd and 4th centuries, such as the Buddha image at Amaravati, and the images of Rama and Kartikeya in the Guntur district of Andhra Pradesh.[14] A further two bronze images of Parsvanatha and a small hollow-cast bull came from Sahribahlol, Gandhara, and a standing Tirthankara (2nd, 3rd century AD) from Chausa in Bihar should be mentioned here as well.[14] Other notable bronze figures and images have been found in Rupar, Mathura (in Uttar Pradesh) and Brahmapura, Maharashtra.[14]


Gupta and post-Gupta period bronze figures have been recovered from the following sites: Saranath, Mirpur-Khas (in Pakistan), Sirpur (District of Raipur), Balaighat (near Mahasthan now in Bangladesh), Akota (near Vadodara, Gujarat), Vasantagadh, Chhatarhi, Barmer and Chambi (in Rajesthan).[14] Producing images by the lost-wax process reached its peak from 750 to 1100, and still remained prevalent in south India between 1500 and 1850.[14] The technique was used throughout India, as well as in the neighbouring countries Nepal, Tibet, Ceylon, Burma and Siam.[15]



Egypt


The Egyptians were practicing cire perdue from the mid 3rd millennium BC, shown by Early Dynastic bracelets and gold jewellery.[17][18] Inserted spouts for ewers (copper water vessels) from the Fourth Dynasty (Old Kingdom) were made by the lost-wax method.[18][19] Hollow castings, such as the Louvre statuette from the Fayum find appeared during the Middle Kingdom, followed by solid cast statuettes (like the squatting, nursing mother, in Brooklyn) of the Second Intermediate/Early New Kingdom.[19] The hollow casting of statues is represented in the New Kingdom by the kneeling statue of Tuthmosis IV (British Museum, London) and the head fragment of Ramesses V (Fitzwilliam Museum, Cambridge).[20] Hollow castings become more detailed and continue into the Eighteenth Dynasty, shown by the black bronze kneeling figure of Tutankhamun (Museum of the University of Pennsylvania). Cire Perdue is used in mass-production during the Late Period to Graeco-Roman times when figures of deities were cast for personal devotion and votive temple offerings.[11]Nude female-shaped handles on bronze mirrors were cast by the lost-wax process.[11]




Late Cycladic (17th century BC) gold ibex sculpture about 10 cm long with lost-wax cast feet and head and repoussé body, from an excavation on Santorini



Greek, Roman and Mediterranean


The lost-wax technique was known in the Aegean during the Bronze Age, particularly in the second millennium BC.[21] Direct imitations and local derivations of Oriental, Syro-Palestinian and Cypriot figurines are found in Late Bronze Age Sardinia, with a local production of figurines from the 11th to 10th century BC.[21]
Some Late Bronze Age sites in Cyprus have produced cast bronze figures of humans and animals. One example is the male figure found at Enkomi.[22] Three objects from Cyprus (held in the Metropolitan Museum of Art in New York) were cast by the lost-wax technique from the 13th and 12th centuries BC, namely, the amphorae rim, the rod tripod, and the cast tripod.[22]
The cremation graves (mainly 8th-7th centuries BC, but continuing until the beginning of the 4th century) from the necropolis of Paularo (Italian Oriental Alps) contained fibulae, pendants and other copper-based objects that were made by the lost-wax process.[23]Etruscan examples, such as the bronze anthropomorphic handle from the Bocchi collection (National Archaeological Museum of Adria), dating back to the 6th to 5th centuries BC, were made by cire perdue.[24] Most of the handles in the Bocchi collection, as well as some bronze vessels found in Adria (Rovigo, Italy) were made using the lost-wax technique.[24]
The better known lost-wax produced items from the classical world include the “Praying Boy” c. 300 BC (in the Berlin Museum), the statue of Hera from Vulci (Etruria), which, like most statues, was cast in several parts which were then joined together.[25] Other, earlier examples that show this assembly of lost-wax cast pieces include the bronze head of the Chatsworth Apollo and the bronze head of Aphrodite from Satala (Turkey) from the British Museum.[26] Geometric bronzes such as the four copper horses of San Marco (Venice, probably 2nd century) are other prime examples of statues cast in many parts.[18]




Moire copper ban, Chu, before 552 BC



East Asia




Wax forms for casting bronze statues for new Tibetan monastery near Kullu, H.P., India


There is great variability in the use of the lost-wax method in East Asia. The casting method of bronze during the Shang and Zhou dynasties (c. 1500–500 BC) has commonly been assumed to be by the lost-mould method.[15] Further investigations have revealed this not to be the case as it is clear that the piece-mould casting method was the principal technique used to manufacture bronze vessels in China.[27] The lost-wax technique did not appear in northern China until the 6th century BC.[28] Lost-wax casting is known as rōgata in Japanese, and dates back to the Yayoi period, c. 200 BC.[15] The most famous piece made by cire perdue is the bronze image of Buddha in the temple of the Todaiji monastery at Nara.[15] It was made in sections between 743 and 749, allegedly using seven tons of wax.[15]



Southeast Asia


The inhabitants of Ban Na Di were casting bronze from c. 1200 BC to 200 AD, using the lost-wax technique to manufacture bangles.[29] (Bangles made by the lost-wax process are characteristic of northeast Thailand.[28]) Some of the bangles from Ban Na Di revealed a dark grey substance between the central clay core and the metal, which on analysis was identified as an unrefined form of insect wax.[28][29] It is likely that decorative items, like bracelets and rings, were made by cire perdue at Non Nok Tha and Ban Chiang.[5]
There are technological and material parallels between northeast Thailand and Vietnam concerning the lost-wax technique.[5] The sites exhibiting artifacts made by the lost-mould process in Vietnam, such as the Dong Son drums, come from the Dong Son, and Phung Nguyen cultures,[5] such as one sickle and the figure of a seated individual from Go Mun (near Phung Nguyen, the Bac Bo Region), dating to the Go Mun phase (end of the General B period, up until the 7th century BC).[29]




The Gloucester Candlestick, early 12th century, V&A Museum no. 7649-1861



Northern Europe


The Dunaverney (1050–910 BC) and Little Thetford (1000–701 BC) flesh-hooks have been shown to be made using a lost-wax process. The Little Thetford flesh-hook, in particular, employed distinctly inventive construction methods.[30][31]
The intricate Gloucester Candlestick (1104–1113 AD) was made as a single-piece wax model, then given a complex system of gates and vents before being invested in a mould.[7]




Detailed 9th century bronze casting by lost wax in form of a coiled snake, Igbo-Ukwu, Nigeria




Sculpture from the Ife state using a lost-wax casting technique, Nigeria, late 11th-14th century.



West Africa


Cast bronzes are known to have been produced in Africa by the 9th century AD in Igboland (Igbo-Ukwu) in Nigeria, the 12th century AD in Yorubaland (Ife) and the 15th century AD in the kingdom of Benin. Some portrait heads remain.[15]



Latin America


The lost-wax casting tradition was developed by the peoples of Nicaragua, Costa Rica, Panama, Colombia, northwest Venezuela, Andean America, and the western portion of South America.[32] Lost-wax casting produced some of the region's typical gold wire and delicate wire ornament, such as fine ear ornaments. The process was employed in prehispanic times in Colombia's Muisca and Sinú cultural areas.[33] Two lost-wax moulds, one complete and one partially broken, were found in a shaft and chamber tomb in the vereda of Pueblo Tapado in the municipio of Montenegro (Department of Quindío), dated roughly to the pre-Columbian period.[34] The lost-wax method did not appear in Mexico until the 10th century,[35] and was thereafter used in western Mexico to make a wide range of bell forms.[36]



Literary history



Indirect evidence




The Berlin Foundry Cup, early 5th century BC


Some early literary works allude to lost-wax casting. Columella, a Roman writer of the 1st century AD, mentions the processing of wax from beehives in De Re Rustica, perhaps for casting, as does Pliny the Elder,[37] who details a sophisticated procedure for making Punic wax.[38]
One Greek inscription refers to the payment of craftsmen for their work on the Erechtheum in Athens (408/7–407/6 BC). Clay-modellers may use clay moulds to make terracotta negatives for casting or to produce wax positives.[38] Pliny portrays[37]Zenodorous [fr] as a well-reputed ancient artist producing bronze statues,[39] and describes[37]Lysistratos of Sikyon, who takes plaster casts from living faces to create wax casts using the indirect process.[39]


Many bronze statues or parts of statues in antiquity were cast using the lost wax process. Theodorus of Samos is commonly associated with bronze casting.[37][40] Pliny also mentions the use of lead, which is known to help molten bronze flow into all areas and parts of complex moulds.[41]Quintilian documents the casting of statues in parts, whose moulds may have been produced by the lost wax process. Scenes on the early-5th century BC Berlin Foundry Cup depict the creation of bronze statuary working, probably by the indirect method of lost-wax casting.[42]



Direct evidence



India


The lost-wax method is well documented in ancient Indian literary sources. The Shilpa shastras, a text from the Gupta Period (c. 320-550 AD), contains detailed information about casting images in metal. The 5th-century AD Vishnusamhita, an appendix to the Vishnu Purana, refers directly to the modeling of wax for making metal objects in chapter XIV: "if an image is to be made of metal, it must first be made of wax."[14] Chapter 68 of the ancient Sanskrit text Mānasāra Silpa details casting idols in wax and is entitled "Maduchchhista vidhānam", or the "lost wax method".[14][15] The Mānasollāsa (also known as the Abhilasitārtha chintāmani), allegedly written by King Bhūlokamalla Someshvara of the Chalukya dynasty of Kalyāni in AD 1124–1125, also provides detail about lost-wax and other casting processes.[14][15]


In a 16th-century treatise, the Uttarabhaga of the Śilparatna written by Srïkumāra, verses 32 to 52 of Chapter 2 ("Linga lakshanam"), give detailed instructions on making a hollow casting.[14][15]



Theophilus


An early medieval writer Theophilus Presbyter, believed to be the Benedictine monk and metalworker Roger of Helmarshausen, wrote a treatise in the early-to-mid-12th century[43] that includes original work and copied information from other sources, such as the Mappae clavicula and Eraclius, De dolorous et artibus Romanorum.[43] It provides step-by-step procedures for making various articles, some by lost-wax casting: "The Copper Wind Chest and Its Conductor" (Chapter 84); "Tin Cruets" (Chapter 88), and "Casting Bells" (Chapter 85), which call for using "tallow" instead of wax; and "The Cast Censer". In Chapters 86 and 87 Theophilus details how to divide the wax into differing ratios before moulding and casting to achieve accurately tuned small musical bells. The 16th-century Florentine sculptor Benvenuto Cellini may have used Theophilus' writings when he cast his bronze Perseus.[15][44]



America


A brief 1596 AD account by the Spanish writer Releigh refers to Aztec casting.[15]



Gallery






  • This bronze piece entitled Lazy Lady, by the sculptor Rowan Gillespie was cast using the lost-wax process.







  • Hugo Rheinhold's Affe mit Schädel is cast out of bronze using the lost-wax process.







  • A wax model is sprued with vents for casting metal and for the release of air, and covered in heat-resistant material.







  • A cast in bronze, still with spruing







  • A bronze cast, with part of the spruing cut away







  • A nearly finished bronze casting. Only the core supports have yet to be removed and closed







  • Illustration of stepwise bronze casting by the lost-wax method







  • The Blätterbrunnen of 1976 by Emil Cimiotti, as seen 2014 in the city center of Hanover, Germany. A lost-wax method was used for the bronze leaves.







Notes





  1. ^ Oxford English Dictionary. [1]


  2. ^ Thoury, M.; et al. (2016). "High spatial dynamics-photoluminescence imaging reveals the metallurgy of the earliest lost-wax cast object". Nature Communications. 7. doi:10.1038/ncomms13356.


  3. ^ abc Moorey, P.R.S. "Early Metallurgy in Mesopotamia"..mw-parser-output cite.citation{font-style:inherit}.mw-parser-output .citation q{quotes:"""""""'""'"}.mw-parser-output .citation .cs1-lock-free a{background:url("//upload.wikimedia.org/wikipedia/commons/thumb/6/65/Lock-green.svg/9px-Lock-green.svg.png")no-repeat;background-position:right .1em center}.mw-parser-output .citation .cs1-lock-limited a,.mw-parser-output .citation .cs1-lock-registration a{background:url("//upload.wikimedia.org/wikipedia/commons/thumb/d/d6/Lock-gray-alt-2.svg/9px-Lock-gray-alt-2.svg.png")no-repeat;background-position:right .1em center}.mw-parser-output .citation .cs1-lock-subscription a{background:url("//upload.wikimedia.org/wikipedia/commons/thumb/a/aa/Lock-red-alt-2.svg/9px-Lock-red-alt-2.svg.png")no-repeat;background-position:right .1em center}.mw-parser-output .cs1-subscription,.mw-parser-output .cs1-registration{color:#555}.mw-parser-output .cs1-subscription span,.mw-parser-output .cs1-registration span{border-bottom:1px dotted;cursor:help}.mw-parser-output .cs1-ws-icon a{background:url("//upload.wikimedia.org/wikipedia/commons/thumb/4/4c/Wikisource-logo.svg/12px-Wikisource-logo.svg.png")no-repeat;background-position:right .1em center}.mw-parser-output code.cs1-code{color:inherit;background:inherit;border:inherit;padding:inherit}.mw-parser-output .cs1-hidden-error{display:none;font-size:100%}.mw-parser-output .cs1-visible-error{font-size:100%}.mw-parser-output .cs1-maint{display:none;color:#33aa33;margin-left:0.3em}.mw-parser-output .cs1-subscription,.mw-parser-output .cs1-registration,.mw-parser-output .cs1-format{font-size:95%}.mw-parser-output .cs1-kern-left,.mw-parser-output .cs1-kern-wl-left{padding-left:0.2em}.mw-parser-output .cs1-kern-right,.mw-parser-output .cs1-kern-wl-right{padding-right:0.2em} In Maddin 1988


  4. ^ ab Muhly, J.D. "The Beginnings of Metallurgy in the Old World". In Maddin 1988


  5. ^ abcdef Agrawal, D. P. (2000). Ancient Metal Technology and Archaeology of South Asia. A Pan-Asian Perspective. New Delhi: Aryan Books International. ISBN 978-81-7305-177-7.


  6. ^ McCreight, Tim (1991). The Complete Metalsmith: An Illustrated Handbook. Davis Publications. ISBN 978-0-87192-240-3.


  7. ^ ab Maryon, Herbert (1954). Metalwork and Enamelling, a Practical Treatise on Gold and Silversmiths' Work and Their Allied Crafts (3rd ed.). Chapman & Hall.


  8. ^ ab Bunker, E.C. Lost Wax and Lost Textile: An Unusual Ancient Technique for Casting Gold Belt Plaques. In Maddin 1988


  9. ^ Zhungeer Banner, western inner Mongolia, 3rd-1st centuries BC


  10. ^ Smith, M.H. (2005). "Breaking the Mould: A Re-evaluation of Viking Age Mould-making Techniques for Oval Brooches". In Bork, R.O. De Re Metallica: The Uses of Metal in the Middle Ages. AVISTA studies in the history of medieval technology, science and art. 4. Ashgate. ISBN 978-0-7546-5048-5.


  11. ^ abc Scheel, B. (1989). Egyptian Metalworking and Tools. Shire Publications. ISBN 978-0-7478-0001-9.


  12. ^ Azarpay, G. (1968). Urartian Art and Artifacts. A Chronological Study. Berkeley and Los Angeles: University of California Press.


  13. ^ Thoury, M.; et al. (2016). "High spatial dynamics-photoluminescence imaging reveals the metallurgy of the earliest lost-wax cast object". Nature Communications. 7. doi:10.1038/ncomms13356.


  14. ^ abcdefghijklmn Kuppuram, Govindarajan (1989). Ancient Indian Mining, Metallurgy, and Metal Industries. Sundeep Prakashan. ISBN 978-81-85067-28-5.


  15. ^ abcdefghijklm Krishnan, M.V. (1976). Cire perdue casting in India. Kanak Publications.


  16. ^ ab Kenoyer, J. M. & H. M.-L. Miller, (1999). Metal Technologies of the Indus Valley Tradition in Pakistan and Western India., in The Archaeometallurgy of the Asian Old World., ed. V. C. Pigott. Philadelphia: The University of Pennsylvania Museum.


  17. ^ Ogden, J., 1982. Jewellery of the Ancient World, London: Trefoil Books.


  18. ^ abc Darling, A. S., (1990). Non-Ferrous Materials, in An Encyclopaedia of the History of Technology, ed. I. McNeil London and New York: Routledge.


  19. ^ ab Ogden, J. (2000). Metals, in Ancient Egyptian Materials and Technology, eds. P. T. Nicholson & I. Shaw Cambridge: Cambridge University Press.


  20. ^ Aldred, G. Egyptian Art in the Days of the Pharaohs 3100 - 320 BC. London: Thames and Hudson.


  21. ^ ab LoSchiavo, F. "Early Metallurgy in Sardinia". In Maddin 1988


  22. ^ ab Schorsch, D.; Hendrix, E. "The Production of Relief Ornament on Cypriot Bronze Castings of The Late Bronze Age". In Archaeometallurgy in Europe 2003


  23. ^ Giumlia-Mair, A.; Vitre, S.; Corazza, S. "Iron Age Copper-Based Finds from the Necropolis of Paularo in the Italian Oriental Alps". In Archaeometallurgy in Europe 2003


  24. ^ ab Bonomi, S.; Martini, G.; Poli, G.; Prandstraller, D. (September 2003). Modernity of Early Metallurgy: Studies on an Etruscan Anthropomorphic Bronze Handle. Archaeometallurgy in Europe. Milan: Associazione Italiana di Metallurgia.


  25. ^ Neuburger, A., 1930. The Technical Arts and Sciences of the Ancients, London: Methuen & Co. Ltd.


  26. ^ Maryon, Herbert (1956). "Fine Metal-Work". In Singer, E. J. H. Charles; Hall, A. R.; Williams, Trevor I. The Mediterranean Civilizations and The Middle Ages c. 700 BC. to c. AD. 1500. A History of Technology. II. Oxford: Clarendon Press. ISBN 978-019858106-2. OCLC 491563676.


  27. ^ Meyers, P. "Characteristics of Casting Revealed by the Study of Ancient Chinese Bronzes". In Maddin 1988


  28. ^ abc White, J.C. "Early East Asian Metallurgy: The Southern Tradition". In Maddin 1988


  29. ^ abc Higham, C. "Prehistoric Metallurgy in Southeast Asia: Some New Information from the Excavation of Ban Na Di". In Maddin 1988


  30. ^ Bowman, Sheridan; Stuart Needham. "The Dunaverney and Little Thetford Flesh-Hooks: history, technology and their position within the Later Bronze Age Atlantic Zone feasting complex". The Antiquaries Journal. The Society of Antiquaries of London. 87. Retrieved 27 June 2010.


  31. ^ Bowman, S (1953). "Late Bronze Age flesh hook, Little Thetford". Cambridgeshire HER. Retrieved 27 June 2010.


  32. ^ Lechtman, H. "Traditions and Styles in Central Andean Metalworking". In Maddin 1988


  33. ^ Scott, D.A. (1991). "Technical Examination of Some Gold Wire from Pre-Hispanic South America". Studies in Conservation. 36 (2): 65–75. doi:10.1179/sic.1991.36.2.65.


  34. ^ Bruhns, K. O. (1972). "Man". Two Prehispanic Cire Perdue Casting Moulds from Colombia.


  35. ^ Hodges, H., 1970. Technology in the Ancient World, London: Allen Lane The Penguin Press.


  36. ^ Hosler, D. "The Metallurgy of Ancient West Mexico". In Maddin 1988


  37. ^ abcd Pliny. Natural History (AD 77).


  38. ^ ab Humphrey, J.W.; Oleson, J.P.; Sherwood, A.N., eds. (2003). Greek and Roman Technology: A Sourcebook: Annotated Translations of Greek and Latin Texts and Documents. Routledge. ISBN 978-1-134-92620-6.


  39. ^ ab Jex-Blake, K. & E. Sellers, 1967. The Elder Pliny's Chapters on The History of Art., Chicago: Ares Publishers, Inc.


  40. ^ Pausania, Description of Greece 8.14.8


  41. ^ Hurcombe, L.M. (2014). Archaeological Artefacts as Material Culture. Routledge. p. 207. ISBN 978-1-136-80200-3.


  42. ^ Mattusch, C.C. (October 1980). "The Berlin Foundry Cup: The Casting of Greek Bronze Statuary in the Early Fifth Century B.C.". American Journal of Archaeology. 84 (4): 435–444. doi:10.2307/504071. JSTOR 504071.


  43. ^ ab Theophilus (Presbyter.) (1963). Hawthorne, John G.; Smith, Cyril Stanley, eds. On Divers Arts: The Foremost Medieval Treatise on Painting, Glassmaking, and Metalwork. Dover. ISBN 978-0-486-23784-8.


  44. ^ M. D. (February 1944). "Cire Perdue". The Scientific Monthly. 58 (2): 158. JSTOR 18097.




References


.mw-parser-output .refbegin{font-size:90%;margin-bottom:0.5em}.mw-parser-output .refbegin-hanging-indents>ul{list-style-type:none;margin-left:0}.mw-parser-output .refbegin-hanging-indents>ul>li,.mw-parser-output .refbegin-hanging-indents>dl>dd{margin-left:0;padding-left:3.2em;text-indent:-3.2em;list-style:none}.mw-parser-output .refbegin-100{font-size:100%}



  • Forbes, R. J. (1971). Metallurgy in Antiquity, Part 1. Early Metallurgy, the Smith and His Tools, Gold, Silver and Lead, Zinc and Bronze. Studies in Ancient Technology. 8. Brill. ISBN 90-04-02652-5.

  • Hart, G. H. & G. Keeley, 1945. Metal Work For Craftsmen, London: Sir Isaac Pitman & Sons.


  • Hodges, H. (1995) [1864]. Artifacts. Bloomsbury Academic. ISBN 978-0-7156-2316-9.

  • Jones, D. M. (ed.) (2001). Archaeometallurgy, London: English Heritage Publications.


  • Konkova, L.V.; Korol, G.G. "South Siberian Imports in Eastern Europe in the 10th — the 13th centuries: Traditions of Metalworking". In Archaeometallurgy in Europe 2003


  • Long, S. (October 1964). "Cire Perdue Copper Casting in Pre-Columbian Mexico: An Experimental Approach". American Antiquity. 30 (2): 189–192. doi:10.2307/278850. JSTOR 278850.

  • McArthur, M., 2005. The Arts of Asia. Materials, Techniques, Styles., London: Thames & Hudson.


  • Noble, J.V. (October 1975). "The Wax of the Lost Wax Process". American Journal of Archaeology. 79 (4): 368–9. doi:10.2307/503070. JSTOR 503070.

  • Taylor, S. E., (1978). Dark-Age Meal Casting; An Experimental Investigation into the Possibility of using Wax Models for the Formation of Clay-Piece Moulds, with special reference to the Manufacture of Pairs of Cast Objects., in The Department of Archaeology Cardiff: University of Cardiff, 97.


  • Trench, Lucy (2000). Materials & Techniques in the Decorative Arts: An Illustrated Dictionary. University of Chicago Press. ISBN 978-0-226-81200-7.


  • Maddin, Robert, ed. (1988). The beginning of the use of metals and alloys: papers from the Second International Conference on the Beginning of the Use of Metals and Alloys, Zhengzhou, China, 21–26 October 1986. MIT Press. ISBN 978-0-262-13232-9. OCLC 644557973.


  • Archaeometallurgy in Europe: International Conference : 24-25-26 September 2003, Milan, Italy : Proceedings. Associazione Italiana di Metallurgia. 2003. ISBN 978-88-85298-50-7.




External links












External video

Bronze Casting (direct method), Smarthistory at Khan Academy, accessed January 6, 2013

Adriaen de Vries's Bronze Casting Techniques, J. Paul Getty Museum, accessed January 22, 2013


  • Andre Stead Sculpture - The Bronze Casting Process

  • Metal Art of Bastar Photos


  • "Flash animation of lost-wax casting process". James Peniston Sculpture. Retrieved 2007-10-24.

  • National Museum of Wildlife Art's Virtual Foundry


  • "Casting a Medal". Sculpture. Victoria and Albert Museum. Retrieved 2007-09-22.

  • Reconstructing the Bronze Age Trundholm Sun Chariot

  • 10/15/1904;The " Cire-perdue " Process of Bronze Casting


  • "André Harvey Lost Wax Process (Cire Perdue)". André Harvey (sculptor). Retrieved 2014-06-18.










-

這個網誌中的熱門文章

12.7 cm/40 Type 89 naval gun

圖片
12.7 cm/40 Type 89 naval gun Type 89 gun mounted on Chitose Type Naval gun anti-aircraft gun Place of origin Japan Service history In service 1932–45 Used by Imperial Japanese Navy Wars World War II Production history Designed 1928–32 Produced 1932–45 No.  built ~1500 Variants Type 88 Specifications Mass 3,100 kilograms (6,834 lb) Barrel length 5,080 millimeters (16 ft 8 in) (bore length) Shell Fixed Shell weight 20.9–23.45 kilograms (46.1–51.7 lb) Caliber 12.7-centimeter (5.0 in) Breech horizontal breech block Elevation -8° to +90° [1] Rate of fire 8-14 rounds per minute Muzzle velocity 720–725 meters per second (2,360–2,380 ft/s) Maximum firing range 9,440 meters (30,970 ft) at 90° (AA ceiling) 14,800 meters (48,600 ft) at 45° The 12.7 cm/40 Type 89 naval gun was a Japanese anti-aircraft (AA) gun introduced before World War II. It was the Imperial Japanese Navy's standard heavy AA...
閱讀完整內容

Rikitea

圖片
Town in French Polynesia, France Rikitea Town Rikitea Location in French Polynesia Coordinates: 23°7′13″S 134°58′9″W  /  23.12028°S 134.96917°W  / -23.12028; -134.96917 Coordinates: 23°7′13″S 134°58′9″W  /  23.12028°S 134.96917°W  / -23.12028; -134.96917 Country   France Overseas collectivity   French Polynesia Territory Gambier Islands Island Mangareva Rikitea is a small town on Mangareva, which is part of the Gambier Islands in French Polynesia. A majority of the islanders live in Rikitea. [1] [2] The island was a protectorate of France in 1871 and was annexed in 1881. [3] Contents 1 History 2 Geography 3 Economy 4 Landmarks 5 Transportation 6 References 7 Bibliography 8 External links History The town's history dates to the era when the island was first settled with people from the Marquesas Islands in 1100 AD. Captain James Wilson of the London Missionary Society arrived in 1797 on Du...
閱讀完整內容

University of Vienna

圖片
"Vienna University" redirects here. For Vienna University of Economics and Business, see Vienna University of Economics and Business. University of Vienna Universität Wien Type Public Established 1365 Budget € 544 million [1] Rector Heinz Engl Academic staff 6,765 Administrative staff 3,106 Students 94,000 [2] Postgraduates 16,490 Doctoral students 8,945 Location Main building, Vienna , Austria 48°12′47″N 16°21′35″E  /  48.21306°N 16.35972°E  / 48.21306; 16.35972 Coordinates: 48°12′47″N 16°21′35″E  /  48.21306°N 16.35972°E  / 48.21306; 16.35972 Campus Urban Colors Blue and White           Affiliations Campus Europae, EUA, UNICA Website www.univie.ac.at/en Data as of 2016 [update] The University of Vienna (German: Universität Wien ) is a public university located in Vienna, Austria. It was founded by Duke Rudolph IV in 1365 and is one of the oldest universities in the Ge...
閱讀完整內容